Panchos Garage v2

Hello!!

Welcome to my page!

On this page I have links for most of the parts I've used to build my 240z. I put links to both eBay and Amazon where available so you can shop around for the best prices. If there is anything I forgot to post on here, feel free to reach out to me on Instagram or Facebook, I'll be more than happy to help out. Also, if anything is broken on here, please let me know as well. Good luck with your projects!! :)

Air Conditioning

Vintage Air Gen II Mini

This is for the main AC unit, it comes with the wiring (which is easy to hook up) and the ducting.

Vintage Air Hose Kit

This kit has all the hoses and 90% of the fittings you'll need to route the AC lines.

AC Compressor

This is the compressor I used.

AC Condenser

12 inch tall x 24 inch wide fits the front of the Z very well.

AC Firewall Bulkhead fitting

This fitting allowed me to get the hsoes from the engine bay to the cabin area.

Control Knobs

I opted into getting these types of knobs to control the AC.

Center Vent

I had to use this as my vent for the center output in the dash.

Mock up Unit

This thing is optional, but its the shape of the AC unit without the weight. It made making the brackets easier.

AC Hose Crimp tool

This is what you need to crimp the AC hoses. Your local AC shop might be able to crimp your hoses, or you can do it at home with this.

AC Compressor Brackets

You'll need these to build your compressor bracket to bolt onto the side of the block.

Fitting

Extra fitting I needed in addition to what's in the kit above.

Fitting

Extra fitting I needed in addition to what's in the kit above.

Heater Hose

This hose in addition to the one right next to this one were used to hook the heater to the unit. No cutting was necessary. Only other thing needed is a 90 degree 5/8 brass fitting and it'll connect to the factory heater hoses.

Heater Hose

This is the other hose.

Brakes

Front Big Brake Kit

Techno Toy Big Brake Kit for the front. Relatively straight forward install. I barely cleared this setup with my 15 inch Konig Rewinds with a small spacer. I'd recommend getting 16 inch wheels if possible.

Rear Big Brake Kit

Same deal with the rear kit, install is straightforward, get 16 inch wheels is possible.

Brake Line Kit

Brand new stainless steel brake line kit. Only thing I didn't like was that they used metric fittings with SAE head sizes. AKA you need an SAE size'd brake fitting tool to get these on tight. Other than that they work good.

Front Wheel Bearings

Front wheel bearing set, they work good.

Rear Wheel Bearings

Rear wheel bearing set, they work good.

1 inch Wilwood Master Cylinder

Since I went with the big front and rear brakes I had to get the 1 inch master instead of the 15/16. You'll need a set of fittings to get these to work with the stock brake lines. I linked the adapter on here as well.

Master Cylinder/Booster Pushrood Length Tool Thing

You need this tool to calculate the length pushrood you need, easy to use.

Master Cylinder Adapter Fittings

You'll need these if you want to install the 1 inch wilwood master with your stock brake lines.

Fuel System

Aeromotive Fuel Pump System

Love this thing. It allows you to install an in-tank fuel pump, just need to cut up your tank a little to get it in there. No more external fuel pumps!

Aeromotive Fuel Pressure Regulator

Same deal with the rear kit, install is straightforward, get 16 inch wheels is possible.

Aeromotive Fuel Filter In-Line

AN6 size inlet and outlet in-line fuel filter with replaceable element.

Aeromotive Fuel Filter Bracket

This bracket I like because I can use it with my in line fuel filter + made a VERY simple plate to mount this in the stock location.

Jenvey Heritage ITBs

Jenvey ITBs, they look like carburators, but they're not!

Harada Intake Manifold

Standard Triple Carb manifold for the L-Series, fit well with the ITBs.

Megasquirt ECU

Got the Megasquirt Gold box with pigtails. So far so good

Heatshield

Standard heat shield for Datsun triple carbs or ITBs.

Heatshield Tape

Used this stuff on the bottom of my heat shield because the exhaust is right in the same area where my ITB wiring is.

Suspension

Front Coilovers

T3 Front Coilover setup.

Rear Coilovers

T3 Rear Coilover setup.

Front Control Arms

T3 Front Control Arm setup.

Rear Control Arms

T3 Rear Control Arm setup.

Coilover Pillow Mounts

Instead of chopping up my strut towers, I went ahead and used these pillow mounts with my coil overs. Allows a bit of camber adjustment.

Steering

Rack and Pinion Boots

Rack and pinion boots, fit the rack perfectly.

Inner Tie Rods

This tie rod is the only one available on the market, its the right (passenger) side. This will fit both passenger and driver side. If replacing the drivers side, please note that you'll also need a passenger side outer tie rod to match. Passenger side inner + driver side outer will NOT work.

Low Profile Outer Tie Rods

Made by Apex Engineering. My tie rods would rub against my 15 inch wheels, these are slim enough to avoid that.

Differential/Axles

CV Boot Kit

Rack and pinion boots, fit the rack perfectly.

Drop Mounts

These aren't really needed, but they look nice.

Mustache Bar

Again, not needed, but looks nice for any R200 swap.

Z31 Companion Flanges

These are needed if you're putting a Z31 LSD differential and CV Axles.

Z31 Half Shafts for S30

These are the shortened Z31 axles for the 240z.